- Purple
- Captive portals: a complete guide
- Public library WiFi procurement checklist: library card sign-in, session limits and filtering
Public library WiFi procurement checklist: library card sign-in, session limits and filtering
You will be able to write a public library WiFi specification that bidders can price accurately. It covers library card sign-in against your LMS, per-branch session and bandwidth limits, IWF-based filtering with an exceptions process, and branch-level reports for councillors. You also get acceptance tests, contract clauses and the cost lines to price.
By James KeanPublished
📖 14 min read3,181 words3 worked examples10 key definitions
Part of our core series: Captive Portal: the complete guide →
- What does a library WiFi specification need to do?
- What do you need before you write the specification?
- Your network estate
- Your library management system
- Your policies
- Your reporting baseline and route to market
- Who owns what
- How do you specify sign-in, session limits and filtering?
- Which sign-in method suits a public library?
- How should session length and bandwidth be limited at busy branches?
- Worked scenario: a central library at peak
- What filtering should a public library network apply?
- Which usage reports does a library service need for councillors and funders?
- What should the contract say about rollout across branches and mobile libraries?
- Worked scenario: a mobile library on a data allowance
- How do you check it works before you sign off?
- What goes wrong, and how do you fix it?
- What does library WiFi cost, and what do you get back?
- Cost lines to price
- What you get back
- Worked scenario: replacing paper vouchers
- Frequently asked questions
- Can readers sign in to library WiFi with their library card number?
- Does Purple work with the access points our branches already have?
- Does Purple Shield apply the IWF list?
- How is Purple priced for a library service?
- Is Purple compliant with UK GDPR for library WiFi?
- Can mobile libraries use the same sign-in, filtering and reports?
- Do readers need to download an app to use library WiFi?

A public library WiFi specification should require library card sign-in, checked live against your library management system. Add an email or SMS route for visitors without a card. Set session and per-device bandwidth limits per branch. Apply the Internet Watch Foundation (IWF) list and your council's acceptable use policy, then report sessions by branch for councillors.
What does a library WiFi specification need to do?
Library WiFi now carries much of the public access offer that once ran only on public PCs. Readers bring their own laptops and phones to study, job hunt, claim benefits and join online appointments. Your specification has to make that easy for readers and defensible for the council.
It has four jobs:
- Identify who is online. Sign-in confirms a library member or a reachable visitor, without collecting more than you need.
- Share capacity fairly. Session and bandwidth limits stop one device from starving a busy branch at 4pm.
- Filter to a standard you can defend. The IWF list is the floor. Your acceptable use policy decides the rest.
- Prove the value. Councillors and funders need branch-level numbers, not anecdotes.
A captive portal does most of this work. A captive portal is the web page a device sees before it reaches the internet, where the visitor signs in or accepts terms. Purple Guest WiFi runs that portal as a cloud overlay on the access points you already own. It handles library card and guest sign-in, session limits and usage reporting across branches. Shield, Purple's filtering add-on, applies filtering per network, including the IWF list.
Purple is live in 80,000+ venues in over 90 countries and sees 500 million users and logins a year, according to Purple's own data. Purple holds ISO 27001, Cyber Essentials and B Corp certification, and is GDPR compliant.
What do you need before you write the specification?
Collect these facts before you draft a single requirement. Bidders price the risk they cannot see, so gaps in your tender push quotes up.
Your network estate
List every branch with its access point make, model and controller. Record the backhaul for each branch: line speed, provider, and whether traffic runs over the council WAN or a separate public line. Purple is hardware-agnostic and runs on Cisco Meraki, HPE Aruba, Ruckus, Juniper Mist, Ubiquiti UniFi, Cambium, Extreme and Fortinet. If your branches run these, you can keep your existing access points. Why your next WiFi upgrade doesn't need new hardware explains the overlay model.
For each mobile library, record the access point, the cellular router, the network operator and the monthly data allowance.
Your library management system
Name your library management system (LMS) supplier and who hosts it. Ask whether SIP2 is enabled. SIP2, the Standard Interchange Protocol version 2 developed by 3M, lets self-service kiosks and other systems check a borrower's card and PIN. Most self-issue machines already use it. If your LMS is shared across a consortium, agree in advance who approves a new connection.
Your policies
- The council's acceptable use policy, plus any library-specific internet policy.
- A Data Protection Impact Assessment (DPIA). UK GDPR Article 35 requires one where processing is likely to create high risk. Public WiFi used by children warrants one.
- Your lawful basis for sign-in data, and a retention period agreed with information governance.
- Accessibility. The Public Sector Bodies (Websites and Mobile Applications) (No. 2) Accessibility Regulations 2018 cover council web content. Specify WCAG 2.2 level AA for every portal page.
Your reporting baseline and route to market
Pull last year's reports to councillors and your CIPFA public library statistics return. Note which WiFi figures you supply today and how you count them. Agree the route to market with procurement under the Procurement Act 2023, which applies to procurements started from 24 February 2025.
Who owns what
| Role | Owns in the specification | Signs off |
|---|---|---|
| Council Libraries Manager | Sign-in routes, session policy, exceptions process, reports | Reader experience and reporting acceptance |
| Council IT Manager | Network design, VLANs, filtering controls, LMS connection | Security and technical acceptance |
| Procurement Officer | Route to market, evaluation criteria, contract clauses | Award and contract terms |
How do you specify sign-in, session limits and filtering?
Which sign-in method suits a public library?
Each route trades friction against identity. The table sets the four common options side by side.
| Sign-in route | What the reader enters | Identity check | Data you hold | Running cost | Best suited to |
|---|---|---|---|---|---|
| Library card and PIN | Card number and PIN | Checked live against the LMS | Card validity result only | No per-login fee; one-off LMS connection | Members at every static branch |
| Email address and acceptance of terms | None unless a confirmation link is sent | Email address | No per-login fee | Visitors, tourists, people joining that day | |
| SMS | Mobile number, then a one-time code | Number confirmed by the code | Verified mobile number | Per-message SMS fee | Branches that need a traceable guest route |
| Click-through | Acceptance of terms only | None | Device and session counts | No per-login fee | Events, overflow and short mobile library stops |
Lead with the library card and offer one guest route beside it. Membership of a public library is free, so the guest screen can link to online joining. A visitor who joins today signs in with a card next week.
Write the card requirement in plain terms:
The portal shall authenticate library card numbers and PINs in real time against the council's LMS, using SIP2 or another documented interface. It shall refuse expired and barred cards with a message directing the reader to staff.
Two details catch services out. First, card barcodes often carry prefixes, check digits or leading zeros. Ask bidders how the portal normalises what a reader types. Second, set a maximum number of devices per card. Two or three covers a phone and a laptop without letting one card serve a study group.
Keep the data minimal, as UK GDPR Article 5(1)(c) requires. The portal needs a valid or invalid answer from the LMS, not borrowing history. If you want to promote events, use conscious-choice opt-ins, unticked by default. 8 smart integration ideas to connect guest WiFi and CRM covers what to do with those opt-ins.
How should session length and bandwidth be limited at busy branches?
Two controls work together. The platform sets session length and when a reader signs in again. The controller enforces per-device rate limits. Cisco Meraki, HPE Aruba and Ruckus all document per-client bandwidth limits in their own configuration guides.
Specify both per branch. A 30-seat community branch and a central library should not share one profile. Your specification should cover:
- Session length. For example, two hours before re-sign-in, ending at closing time.
- Daily allowance. An optional cap per card per day at busy branches.
- Per-device rate limits. Separate download and upload limits per profile.
- Reserved capacity. A guaranteed share of the line for public PCs, self-service kiosks and staff, on separate VLANs. A VLAN (virtual local area network) isolates traffic on shared hardware.
- Time-of-day profiles. Tighter limits for after-school and exam-season peaks.
Worked scenario: a central library at peak
Situation. A central library has a 200 Mbps line shared by 30 public PCs, self-issue kiosks, staff devices and public WiFi. After school, WiFi reaches around 150 connected devices. Large downloads slow the public PCs, which host booked job-search sessions.
What was done. IT moved PCs, kiosks and staff onto separate VLANs and reserved 60 Mbps for them at the WAN edge. Public WiFi received the remaining 140 Mbps. Each device was capped at 3 Mbps down and 1.5 Mbps up, with two-hour sessions on library card sign-in.
Measurable outcome. The public PCs keep a 60 Mbps floor whatever WiFi demand does. No single device can take more than about 2% of the WiFi pool. Zoom's published requirements list 1.2 Mbps up and down for a one-to-one 720p HD call. So 40 simultaneous interview calls use 48 Mbps, leaving 92 Mbps for the other 110 devices.
What filtering should a public library network apply?
Start with the non-negotiable layer. The IWF URL list identifies webpages hosting child sexual abuse imagery and is updated twice a day. Your specification should require it on every public network, with no override.
Then add the categories your acceptable use policy names. These typically include pornography, malware and phishing. Some councils also apply the police-assessed list of unlawful terrorist content produced on behalf of the Home Office. Ask each bidder whether they can apply it. Many councils also seek Friendly WiFi accreditation, the UK scheme for public WiFi filtered for pornography and child sexual abuse content.
Filtering per network lets you set different policies for public, children's area and staff networks. Shield applies filtering this way. For a deeper look at multi-site filtering controls, see Guest WiFi and DNS filtering platforms for MSPs: a multi-site checklist for multi-tenant management and white label.
Over-blocking is a real risk in libraries. Category filters can catch sexual health, LGBTQ+ support and domestic abuse services. CILIP's Ethical Framework commits members to intellectual freedom, so your exceptions process matters as much as the block list. Write it into the specification:
- The block page explains the policy and links to a review request.
- A named officer decides each request within five working days.
- Approved sites go onto a per-network allow list.
- Every decision is logged for audit.
- The IWF list sits outside the allow list and cannot be overridden.
Ask bidders how the filter handles DNS over HTTPS (DoH), which encrypts DNS lookups and can bypass DNS-based filtering.
Which usage reports does a library service need for councillors and funders?
Reports should answer three questions. Who uses the service? Where is demand highest? Is it reliable? WiFi Analytics provides branch-level dashboards and exports.
| Report | Audience | Frequency | What it shows |
|---|---|---|---|
| Unique visitors and sessions per branch | Councillors, cabinet member | Quarterly | Reach of the service across wards |
| Card versus guest sign-ins | Libraries Manager | Monthly | Membership conversion from guest routes |
| Peak concurrent devices by hour | IT Manager | Monthly | Where capacity or session limits need adjusting |
| Average session length | Libraries Manager, funders | Quarterly | Depth of use for study and digital inclusion |
| Filtering blocks by category, aggregated | Information governance | Quarterly | Policy working without individual-level records |
| Availability per branch and mobile library | IT Manager, Procurement Officer | Monthly | Supplier performance against the contract |
Specify scheduled CSV exports so figures drop straight into your CIPFA return and committee papers. Keep filtering reports aggregated. Councillors need patterns, not browsing records of named readers.
What should the contract say about rollout across branches and mobile libraries?
Write rollout as a sequence with acceptance gates, not a single go-live date:
- Pilot. One busy branch and one small branch, run against the acceptance tests in the next section.
- Phased waves. Groups of branches, scheduled outside opening hours.
- Mobile libraries. Tested at real stops, including those with weak signal.
- Close-out. Paper vouchers withdrawn, staff trained, reports signed off.
Add these clauses:
- Support hours that cover Saturday opening, with response times per severity.
- Platform availability commitments. Purple's platform runs at 99.999% uptime.
- Article 28 UK GDPR processor terms, data location, retention and deletion on exit.
- Evidence of ISO 27001 and Cyber Essentials certification, renewed annually.
- Change control for filtering categories and exceptions.
- An exit plan with data export in a stated format.
- Line-by-line pricing per static branch and mobile library, so sites can be added or closed.
Worked scenario: a mobile library on a data allowance
Situation. A county service runs one mobile library on a 4G connection with a 150 GB monthly data allowance. It makes around 40 stops a month, with up to eight readers online per stop.
What was done. The vehicle shows the same portal and filtering as static branches, with card or click-through sign-in. Sessions were set to 30 minutes, with a 2 Mbps cap per device.
Measurable outcome. At 2 Mbps, a 30-minute session can use at most 450 MB. The worst case of 320 full-rate sessions uses 144 GB, inside the 150 GB allowance. One busy afternoon can no longer exhaust the month's data.
Got questions about your specific setup?
Our team works with venue operators, IT managers, and network engineers across 80,000 venues. Book a 20-minute call and we will show you how others like you solved it.
How do you check it works before you sign off?
Run these tests at the pilot branches, and repeat them at every wave. Record each result in the acceptance log.
Sign-in
- Valid card and PIN connects. Expired, barred and wrong-PIN cards are refused with the agreed message.
- Card numbers with leading zeros and prefixes work.
- The device limit per card holds at the agreed number.
- Email and SMS routes deliver and accept a code or confirmation.
Sessions and bandwidth
- Sessions end at the set length and at closing time.
- A speed test on two devices shows each capped at the profile limit.
- Public PCs keep their reserved capacity while WiFi is loaded.
Filtering
- Your filtering provider's test page is blocked on every public network.
- Each blocked category returns the block page with the review link.
- A test exception request completes end to end within the agreed time.
- Public devices cannot reach the staff or public PC VLANs.
Portal and reports
- The portal works on iOS, Android, Windows, macOS and ChromeOS.
- It passes WCAG 2.2 level AA checks with a screen reader and keyboard only.
- One week of sign-in figures reconciles sensibly against door counter data.
What goes wrong, and how do you fix it?
| Problem | Likely cause | Fix |
|---|---|---|
| Valid cards are refused | Barcode format mismatch, or the SIP2 account is locked | Normalise card formats in the portal; give the WiFi check a dedicated SIP2 account with monitoring |
| Nobody can sign in at any branch | LMS outage or maintenance window | Open the guest route automatically while the LMS is unreachable |
| Visitor counts look inflated | MAC randomisation on iOS and Android gives one device several addresses | Report on authenticated sign-ins by card or verified contact, not raw device addresses |
| The sign-in page does not appear | Pre-sign-in allow list or DNS misconfigured | Check the controller's allow list for the portal domains against the vendor's documentation |
| Legitimate health or support sites are blocked | Category filters set too broadly | Use the exceptions process and review category choices quarterly |
| Filtering is bypassed | Encrypted DNS or VPN apps | Apply your policy on known DoH resolvers and cover VPNs in the acceptable use policy |
| Mobile library sessions drop between stops | Cellular signal lost on the road | Accept re-sign-in at each stop and keep sessions short |
MAC randomisation is the one that most often distorts reports. A MAC address is a device's hardware identifier, and modern phones now vary it per network. Counting sign-ins by card or verified contact gives councillors a figure that survives this change.
What does library WiFi cost, and what do you get back?
Cost lines to price
- Platform licence. Purple prices through three plans: Connect, Capture and Engage.
- Filtering. Shield as an add-on, alongside SecurePass and Verify.
- SMS. A per-message fee if you offer an SMS route.
- LMS connection. Any set-up charge from your LMS supplier for a new SIP2 account.
- Hardware. Often none where branches run supported access points.
- Mobile data. The cellular contract for each vehicle.
- Staff time. Training and the exceptions process.
What you get back
The biggest return is usually staff time at the counter. The second is evidence: branch-level numbers that support budget decisions. The third is a filtering standard you can defend at committee.
Worked scenario: replacing paper vouchers
Situation. A 15-branch service issues paper WiFi vouchers at the counter. Each branch issues around 30 a day, at roughly two minutes per voucher, six days a week.
What was done. The service switched to library card sign-in, with an email route for visitors without a card.
Measurable outcome. Voucher handling had consumed 15 staff hours a day across the service, or 90 hours a week. Card sign-in removes that counter task entirely. Staff time returns to reader enquiries, and every session now appears in the branch reports.
The same identity principles apply to staff networks. What is user provisioning? a plain-english guide for 2026 covers automating staff access when you extend the project.
Frequently asked questions
Can readers sign in to library WiFi with their library card number?
Yes. Purple supports library card sign-in, so readers enter their card number and PIN on the captive portal. Purple checks the details against your library management system and refuses expired or barred cards with a message pointing the reader to staff. Ask your LMS supplier to confirm the connection method, usually SIP2, and to issue a dedicated account for the check. Visitors without a card use an email or SMS route instead.
Does Purple work with the access points our branches already have?
Yes, if they are one of the supported makes. Purple is hardware-agnostic and runs as a cloud overlay on Cisco Meraki, HPE Aruba, Ruckus, Juniper Mist, Ubiquiti UniFi, Cambium, Extreme and Fortinet. If your branches run these, you keep your existing access points and controllers, with no rip and replace. List the make, model and controller for every branch and mobile library in your tender, so bidders can confirm compatibility site by site.
Does Purple Shield apply the IWF list?
Yes. Shield applies filtering per network, including the Internet Watch Foundation list of webpages hosting child sexual abuse imagery. You then add the categories your council's acceptable use policy requires, such as pornography, malware and phishing. Because filtering runs per network, your public, children's area and staff networks can carry different policies. Your exceptions process can unblock wrongly filtered sites, but the IWF list should never be overridable.
How is Purple priced for a library service?
Purple prices through three plans - Connect, Capture and Engage - with Shield, SecurePass and Verify available as security add-ons. A library service needs sign-in, session limits and reporting from its plan, plus Shield for filtering. Ask for a quote that lists each static branch and mobile library as its own line. That lets you add, close or merge sites during the contract without renegotiating the whole agreement.
Is Purple compliant with UK GDPR for library WiFi?
Yes. Purple is GDPR compliant and certified to ISO 27001 and Cyber Essentials. For library card sign-in, the portal needs only a valid or invalid answer from your LMS, not borrowing records, which supports data minimisation under UK GDPR Article 5. Your contract should set out controller and processor roles under Article 28, retention periods and deletion on exit. Complete a DPIA before go-live, because public WiFi used by children carries extra risk.
Can mobile libraries use the same sign-in, filtering and reports?
Yes, where the vehicle's access point is one of the supported makes and has a cellular connection. The mobile library then shows the same captive portal and applies the same Shield filtering as your static branches. Set shorter sessions and a lower per-device cap, so the monthly data allowance holds. Ask bidders to describe what readers see when the cellular signal drops at a stop, and test it at real stops.
Do readers need to download an app to use library WiFi?
No. Readers sign in through the captive portal in their device's browser, using a library card, email, SMS or click-through route. Nothing needs installing, which matters for readers on older or shared devices. Specify that the portal meets WCAG 2.2 level AA and works on iOS, Android, Windows, macOS and ChromeOS. Then test each platform, with a screen reader and keyboard only, during acceptance at your pilot branches.
Key Definitions
Captive portal
A web page an unauthenticated device is redirected to before it reaches the internet, where the visitor signs in or accepts terms. Pre-sign-in access is governed by an allow list of portal domains on the WiFi controller.
The portal carries library card, email, SMS and click-through sign-in. If the controller's allow list or DNS is misconfigured, the sign-in page does not appear, so check it against the vendor's documentation.
SIP2
Standard Interchange Protocol version 2, developed by 3M, which lets self-service kiosks and other systems check a borrower's card number and PIN against a library management system.
Most self-issue machines already use it. Ask your LMS supplier whether it is enabled and request a dedicated, monitored SIP2 account for the WiFi check, so a locked account does not refuse valid cards.
IWF URL list
The Internet Watch Foundation's list of webpages hosting child sexual abuse imagery, updated twice a day for use by filtering providers.
This is the non-negotiable filtering floor for every public library network. It sits outside your allow list and must never be overridable by the exceptions process.
Data Protection Impact Assessment (DPIA)
An assessment required by UK GDPR Article 35 where processing is likely to result in a high risk to individuals' rights and freedoms.
Public WiFi used by children warrants one. Complete it before go-live, alongside your lawful basis and a retention period agreed with information governance.
Data minimisation
The principle in UK GDPR Article 5(1)(c) that personal data must be adequate, relevant and limited to what is necessary for the purpose.
The portal needs only a valid or invalid answer from the LMS, not borrowing history. Specify this so bidders cannot pull more reader data than sign-in requires.
Article 28 processor terms
UK GDPR Article 28 sets the contract terms a controller must have with a processor, including processing only on documented instructions and deletion or return of data at the end of the service.
Your contract should set controller and processor roles, data location, retention and deletion on exit, plus an exit plan with data export in a stated format.
VLAN
A virtual local area network, defined by IEEE 802.1Q, which isolates traffic on shared switching and wireless hardware by tagging frames with a network identifier.
Put public PCs, self-service kiosks and staff on separate VLANs from public WiFi, then reserve capacity for them and test that public devices cannot reach those networks.
DNS over HTTPS (DoH)
A method specified in IETF RFC 8484 that encrypts DNS lookups inside HTTPS, which can bypass DNS-based filtering.
Ask bidders how their filter handles DoH, and apply your policy on known DoH resolvers so readers cannot sidestep the IWF list and your acceptable use policy.
WCAG 2.2 level AA
The W3C Web Content Accessibility Guidelines version 2.2 at conformance level AA, the accessibility standard UK councils apply under the Public Sector Bodies (Websites and Mobile Applications) (No. 2) Accessibility Regulations 2018.
Specify it for every portal page and test with a screen reader and keyboard only during acceptance at your pilot branches.
MAC randomisation
A privacy feature on iOS and Android where a device presents a different MAC address, its hardware identifier, per WiFi network rather than a fixed one.
It gives one device several addresses and inflates visitor counts. Report on authenticated sign-ins by card or verified contact so councillors get a figure that survives the change.
Worked Examples
A central library has a 200 Mbps line shared by 30 public PCs, self-issue kiosks, staff devices and public WiFi. After school, around 150 devices connect to WiFi and large downloads slow the public PCs hosting booked job-search sessions. How should capacity be shared?
IT moved the PCs, kiosks and staff onto separate VLANs and reserved 60 Mbps for them at the WAN edge, leaving 140 Mbps for public WiFi. Each device was capped at 3 Mbps down and 1.5 Mbps up, with two-hour sessions on library card sign-in. The public PCs now keep a 60 Mbps floor whatever WiFi demand does, and no single device can take more than about 2% of the WiFi pool. Using Zoom's published 1.2 Mbps for a one-to-one 720p call, 40 simultaneous interview calls use 48 Mbps, leaving 92 Mbps for the other 110 devices.
A county mobile library runs on a 4G connection with a 150 GB monthly data allowance. It makes around 40 stops a month, with up to eight readers online per stop. How do you stop one busy afternoon exhausting the month's data?
The vehicle shows the same captive portal and filtering as static branches, with card or click-through sign-in. Sessions were set to 30 minutes with a 2 Mbps cap per device. At 2 Mbps, a 30-minute session can use at most 450 MB. The worst case of 320 full-rate sessions uses 144 GB, which sits inside the 150 GB allowance. Shorter sessions also suit the road, because readers re-sign-in at each stop when the cellular signal drops between them.
A 15-branch service issues paper WiFi vouchers at the counter. Each branch issues around 30 a day at roughly two minutes per voucher, six days a week. What does switching to library card sign-in return?
The service replaced vouchers with library card sign-in and added an email route for visitors without a card. Voucher handling had consumed 15 staff hours a day across the service, or 90 hours a week. Card sign-in removes that counter task entirely, so staff time returns to reader enquiries. Every session now appears in the branch reports, giving councillors and funders branch-level numbers rather than anecdotes. Because public library membership is free, the guest screen can also link to online joining, converting visitors into members.
Frequently asked questions
Can readers sign in to library WiFi with their library card number?
Yes. Purple supports library card sign-in, so readers enter their card number and PIN on the captive portal. Purple checks the details against your library management system and refuses expired or barred cards with a message pointing the reader to staff. Ask your LMS supplier to confirm the connection method, usually SIP2, and to issue a dedicated account for the check. Visitors without a card use an email or SMS route instead.
Does Purple work with the access points our branches already have?
Yes, if they are one of the supported makes. Purple is hardware-agnostic and runs as a cloud overlay on Cisco Meraki, HPE Aruba, Ruckus, Juniper Mist, Ubiquiti UniFi, Cambium, Extreme and Fortinet. If your branches run these, you keep your existing access points and controllers, with no rip and replace. List the make, model and controller for every branch and mobile library in your tender, so bidders can confirm compatibility site by site.
Does Purple Shield apply the IWF list?
Yes. Shield applies filtering per network, including the Internet Watch Foundation list of webpages hosting child sexual abuse imagery. You then add the categories your council's acceptable use policy requires, such as pornography, malware and phishing. Because filtering runs per network, your public, children's area and staff networks can carry different policies. Your exceptions process can unblock wrongly filtered sites, but the IWF list should never be overridable.
How is Purple priced for a library service?
Purple prices through three plans - Connect, Capture and Engage - with Shield, SecurePass and Verify available as security add-ons. A library service needs sign-in, session limits and reporting from its plan, plus Shield for filtering. Ask for a quote that lists each static branch and mobile library as its own line. That lets you add, close or merge sites during the contract without renegotiating the whole agreement.
Is Purple compliant with UK GDPR for library WiFi?
Yes. Purple is GDPR compliant and certified to ISO 27001 and Cyber Essentials. For library card sign-in, the portal needs only a valid or invalid answer from your LMS, not borrowing records, which supports data minimisation under UK GDPR Article 5. Your contract should set out controller and processor roles under Article 28, retention periods and deletion on exit. Complete a DPIA before go-live, because public WiFi used by children carries extra risk.
Can mobile libraries use the same sign-in, filtering and reports?
Yes, where the vehicle's access point is one of the supported makes and has a cellular connection. The mobile library then shows the same captive portal and applies the same Shield filtering as your static branches. Set shorter sessions and a lower per-device cap, so the monthly data allowance holds. Ask bidders to describe what readers see when the cellular signal drops at a stop, and test it at real stops.
Do readers need to download an app to use library WiFi?
No. Readers sign in through the captive portal in their device's browser, using a library card, email, SMS or click-through route. Nothing needs installing, which matters for readers on older or shared devices. Specify that the portal meets WCAG 2.2 level AA and works on iOS, Android, Windows, macOS and ChromeOS. Then test each platform, with a screen reader and keyboard only, during acceptance at your pilot branches.
Continue reading in this series
Event venue WiFi providers: per-event captive portals, exhibitor access and attendee reporting
You will be able to choose between temporary contractors, vendor splash pages, organiser-supplied networks and a cloud overlay for your event venue. You will also be able to specify per-event captive portals, expiring exhibitor keys and sponsor-ready attendance reports. Finally, you can settle who controls attendee data under UK GDPR before the first portal goes live.
Ruckus SmartZone and RUCKUS One guest WiFi vs external captive portal platforms
Decide whether native Ruckus SmartZone or RUCKUS One guest access covers your estate, or whether an external captive portal such as Purple is worth its subscription. You can map your sites, vendors and data ownership to a clear recommendation. You will also understand the WISPr, Northbound Interface and RADIUS integration, and the cost of each option.
Aruba Central guest WiFi vs dedicated captive portal platforms: CRM, Passpoint and reporting compared
Use this comparison to choose between Aruba Central's native Cloud Guest, ClearPass Guest and a dedicated cloud platform such as Purple for your HPE Aruba estate. You can match each option to who owns guest WiFi, where guest data must land, how you record GDPR consent, whether returning guests need Passpoint and what each option costs over three years.
Got questions about your specific setup?
Our team works with venue operators, IT managers, and network engineers across 80,000 venues. Book a 20-minute call and we will show you how others like you solved it.